Car Paint Prices Auto Paint Chip Repair
1K basecoat High quality,multiple layers basecoat system with metal colour basecoat for high class cars and commercial vehicles. 1.The result will be perfect if the users use Roch® brand supporting thinners. 2.Light...
When you need hard-working, absolutely reliable coatings and color, trust Roch® Refinish. From basecoats to topcoats, we provide the options and quality you demand, with the innovative solutions that keep your shop efficient and profitable.
ROCH RC-M and S series Basecoat
An advanced nano-encapsulation technology that allows for higher pigment, metallic, and pearl concentration while providing superior particle orientation and ease of blending.Allows for maximum coverage with minimal coats. Provides outstanding color-match flexibility and optimum repairability. Enables outstanding adhesion and rapid tape and dry times for fast repairs.
1.Allows for maximum coverage with minimal coats.
2.Provides outstanding color-match flexibility and optimum repairability.
3.Enables outstanding adhesion and rapid tape and dry times for fast repairs.
More than 2,000 OEM color formulations are documented in the Jinwei Global Color Box.
RC-M Series High Performance Base Color
RC-X110 Reducer Fast
RC-X111 Reducer Standard
RC-X112 Reducer Slow
RC-X113 Reducer Very Slow
2. MIXING RATIO (1:0.7-1 by volume)
NOTE: We only recommend activator in basecoat for under hood
applications where the basecoat will not be over coated
3. POT LIFE @ 25°C
When properly covered at 25°C, RC-M Series Base will maintain a sprayable viscosity indefinitely
4. CLEAN UP
Use ROCH Refinish Reducers listed above (check local regulations)
5. SURFACE PREPARATION
Surfaces should be prepared using the proper undercoat system following recommended procedures
All surfaces should be finish sanded with 600/P800 grit wet or dry sandpaper or equivalen
RC-3000 MS Clear Coat
RC-8000 Mirror Effect Clear Coat
RC-9000 HS Clear Coat
RC-4700 Fast drying Clear Coat
Properly prepared previously painted surfaces
ROCH 2K primers RC-D505 and sealers RC-D400
Spray two (2) to three (3) medium-wet coats with an overlap of 75%
until hiding and color match are achieved.
If necessary for metallic orientation a final drop coat RC-B160 may be used
Allow each coat 5-10 minutes flash or until finish is dull.
Dry mils 2.0 to 3.0 mils (20-75 μm). Wet mils 4.0 to 6.5 mils (100-165 μm)
Surface temperature should be 10-35°C with less than 80% ambient humidity preferred
Acrylic resin, CAB, pigment, solvents, addition agents
All kinds of colors. For detailed information please refer to Roch® Tinters in the catalog
1K paint: 1 part
Thinner(RC-X110, RC-X111, RC-X112): 0.7~1 parts
|Pot Life||48 hours@20℃|
Spray Gun &
|2-3 single coating to coverage (volatilization time of each layer: 15-20 minutes)|
|Drying Time||Clearcoat can be sprayed within 15 minutes to 5 hours|
Before spray: P600-800 by dry sanding
After spray: P1000 by wet sanding
|Substrate||OEM paint, Roch® brand primer surfacer|
|Thermal plasticity acrylic paint or alloy base coat|
1L x 12 tins/ctn, 4L x 4 tins/ctn
Metallic and pearl colors:
Apply one single coat, allow flash off until the coat is completely dried (matt). Apply a following lighter coat till covering is achieved. If necessary , finish with a mist coat by reducing the working pressure with 0.5 bar at the air inlet and increase the distance between spray-gun and object.
Apply one full single coat. Allow flash off until the coat is completely matt. Apply another single coat and again allow this coat to flash off until matt, repeat until covering is achieved, a mist coat is not needed with solid colors.
Spot and fade-out repair:
Apply the basecoat in thin (overlapping) coats with the spray gun fully triggered at a spraying pressure of 1.5-1.8 bar until opacity is achieved. Allow to flash off until matt between coats, than fade out twice into remaining area (only metallic colors), using a spraying pressure of 1.5 – 1.8bar.
-Metallic toners must be stirred thoroughly before using for the first time
-While making a spot repair, it’s not necessary to tag-rag between coats
-Apply a full coat of pure 7000 as a first coat for a better orientation of the metallic
-With metallic 50% of pure 7000 can be added to the final (drop)coat
-Do not apply to heavy coats while making a spot repair
-Jinwei Basecoat oil base is in principle ready for use Addition of Activator is possible for:
- adjusting the viscosity of light metallics - avoiding overspray while painting larger objects
- painting in warm and/or dry conditions (low RH) Mixed colors must be stirred thoroughly directly after mixing, prior adding Activator
- If a pure Basecoat oilbase metallic mixing color will be applied, always add Basecoat oilbase tinter RC-X111 in a mixing ratio 1:4 (1part Metallic :4 parts RC-X111)
- Adding 5% of Additive Long Potlife increases the potlife of metallics up to 3 months
- Clean spray gun with waterborne Guncleaner directly after use
Per coat: 10-20 µm
Recommended application (2 coats): 20-30 µm
Ready for use mixture at recommended layer thickness per coat 7.5 m²/liter
The practical coverage depends on many factors i.e. shape of the object, roughness of the surface, application method and application circumstances.
2017 Automechanika Dubai
lOADING THE CONTAINER
PACKING & DELIVERY
BENEFITS WE OFFER
If you want the car paint prices auto paint chip repair, welcome to buy the quality products made in China with our factory. As one of the professional manufacturers in China, we will offer you quality products with low price. Consult the quotation with us now.