Guangzhou Jinwei Chemical Co., Ltd

Automotive Refinish Paint One Stop Supplier. Professional Team, Perfect Service!

Clearcoat Solutions

Clearcoat Solutions

High Efficiency Clearcoat RC-9000 Clearcoat has highest gloss, highest build, best exterior durability, highest end hardness and good adhesion results on metallic basecoats, good leveling. The application function is good and it is fast drying coat.

Send InquiryChat Now
Product Details

PREMIUM APPEARANCE CLEARCOAT RC-9000

GENERAL DESCRIPTION 
A two-component, urethane clearcoat that delivers unsurpassed appearance for premiumquality panel, multi-panel and overall repairs. The products referenced herein may not be sold in your market. Please consult our distributor for product availability. 


MIXING COMPONENTS/RATIO 

ROCH® Colordefender™ Premium Appearance Clearcoat RC-9000    2 Parts
Activator  RC-G333(K/B/M)     1 Part
Reducer RC-X110/X111/X112       0.2 Part


VISCOSITY 

15-17 seconds in a Zahn #2 cup.


POT LIFE 

90 minutes at 70°F (21°F)


ADDITIVES 

Accelerator/Fish Eye Eliminator/Flex Additive/Matting Agent


APPLICATION SUBSTRATES 

1K Basecoat RC-M series 


SURFACE PREPARATION 

For application over a properly prepared basecoat repair: 

 Mask the entire vehicle to protect from overspray. 

 Allow basecoat to dry 15-30 minutes prior to clearcoat application. 

 Extend basecoat flash to 30 minutes when applying several base color coats, tri-coat colors, or in cooler shop conditions. 


GUN SETUPS* 

Compliant 1.3 mm-1.4 mm* 

HVLP 1.3 mm-1.4 mm* 


AIR PRESSURE* 

Compliant 

Siphon Feed    50-55 psi at the gun 

Gravity Feed     45-55 psi at the gun 

HVLP     9-10 psi at the gun cap 

*Refer to the manufacturer's directions for gun specific recommendations.


APPLICATION 

Apply 2 medium-wet coats. Flash 12-15 minute between coats.


Tips for Success 

 Use a high atomizing air cap for best results. 

 Follow proper bake recommendations depending on the choice of activator. Bake recommendations are a guide and need to be adjusted for non-recirculating and recirculating booths. 

 Observe proper flash times, especially in overlap areas where there is a tendency to have excessive film build. 

 Proper tip size and air pressure is important for consistent film build and performance. 

 Increased flash time between coats to 15 minutes for air dry situations. The air flow in the booth must be left on for at least an hour following application of the clear.


DRY TIMES 

FORCE DRY 

Flash between Coats12-15 minutes
Flash before force dryNone
Cycle Time15 minutes at 70°C
Dust FreeAt cool Down
Time to Polish3 hours after cool down
Time to Handel30 minutes after cool down

AIR DRY

Flash between Coats12-15 minutes
Dust Free30-35 minutes
Time to Polish8 hours 
Time to Handel8 hours


BLENDING 

Panel repair is the approved procedure for clearcoat warranty repairs. This allows the refinisher to attain the recommended film builds. 


CLEANUP 

Clean spray equipment as soon as possible with Lacquer Thinner.


SANDING / COMPOUNDING / POLISHING SANDING 

 Use 1500 grit wet or finer or use a foam interface pad with P1500 DA or finer. 

COMPOUNDING 

 Apply a thin ribbon of rubbing compound to the area that was sanded or contains sand scratches. 

 Maintain air polisher or variable speed buffer at 1400-1800 rpm. Remove excess finishing compound with a clean soft cloth prior to applying finishing polish. 

 Use a wool pad and an effective rubbing compound. 

POLISHING 

 Apply a ribbon of polishing material to the area to be polished. 

 Maintain a variable speed buffer or an orbital polisher at 1400-1800 rpm. 

 Use a foam pad and an effective polishing compound. Keep the polisher/buffer moving at all times. Overlap each pass approximately 50%. As finishing polish begins to dry, stop polishing. 

 Wipe off excess finishing polish with a clean soft cloth. 

 Hand buff with a clean soft cloth as a finishing touch. 


Tips for Success 

 Always use clean water to wet sand and add a few drops of soap to help clear the paper. 

 Always use a foam interface pad when DA sanding. 

 Use clean cloths and pads to insure that the clear does not get scratched with dirt.


PHYSICAL PROPERTIES 

All Values Ready To Spray 

                                                                      Standard Reduction Mix Ratio  2:1:0.2-0.5

Max.VOC(LE)466 g/L
Max.VOC(AP)438 g/L
Avg.Gal.Wt.980 g/L
Avg.Wt.%Volatiles48.1%
Avg.Wt.%Exempt Solvent6%
Avg.Vol.%Exempt Solvent5.9%
Theroetical Coverage:700 sq. ft. per RTS gallon at 1 mil
Recommended Dry Film Thickness:2.0 – 2.4 mils in 2 coats.
Packaging5L x 4 tins/ctn, 1L x 12 tins/ctn
Shelf Life5 years


VOC REGULATED AREAS 

These directions refer to the use of products which may be restricted or require special mixing instructions in VOC regulated areas. Follow mixing usage and recommendations in the VOC Compliant Products Chart for your area. 


SAFETY AND HANDLING 

For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and MSDS/SDS precautions. If mixed with other components, mixture will have hazards of all components. 

Ready to use paint materials containing isocyanates can cause irritation of the respiratory organs and hypersensitive reactions. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates. 

Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying respirator with particulate filters or appropriate ventilation, and gloves.


PROCESS

Keep it for 15 to 20 minutes after spray, and then bake it.


PRECAUTIONS

1.Keep the baking room dry when baking, otherwise the gloss will disappear.

2.Add 15‰ quick dry liquid for fast solidity.

3.Choose the right hardener according to the tempreture.

It is suitable to spray the whole car body.


DETAIL IMAGES

家族照.jpg

Gasser Green_副本.jpg

CTV 1L 增彩.jpgCTV 1L P.JPGCTV 4L.JPG



OUR FACTORY


OUR WORKSHOP

Jinwei Refinish supplies high quality car paint colour mixing system ranging from LOW VOC, High solid Low viscosity Tinting System, conventional acrylic systems to accessory products such as primers, surfacers, base coat, top-coat, clear coat,  hardener, thinner, and ancillary materials etc., We are able to provide more competitive and cost effective color mixing system than comparable systems on the market.


EXHIBITION


2017 Automechanika Dubai



PACKING & DELIVERY

HTB1mcTgXbSYBuNjSspfq6AZCpXaU_看图王.jpg



BENEFITS WE OFFER

Help customers achieve their goals while driving productivity from the front of the body shop to the back. For coatings systems engineered for easy, quick and accurate application. For localized business and marketing support solutions. And for pragmatic innovations that simplify and expedite the refinish process. 

With our products and support, we help body shops focus on driving their businesses forward.



FAQS

1. Do you charge for the samples?
(A) According to our company policy, the samples are free, we only charge the freight. And we will return the freight if you set the order .


2. Can you produce the product according to customer's requirement?

(A) Sure, we are professional manufacturer, OEM is welcome.


3. What about the quality?

(A) We can provide you samples for quality inspection. If you order to us ,we must promise the quality , if some quality problem happened, we can have a negotiation of the compensation and sign agreements ,and our after-sales department will perform the duties as the agreements.


If you want the High Build Car Paint for body shop, welcome to buy the quality products made in China with our factory. As one of the professional manufacturers in China, we will offer you quality products with low price. Consult the quotation with us now.


If you want the clearcoat solutions, welcome to buy the quality products made in China with our factory. As one of the professional manufacturers in China, we will offer you quality products with low price. Consult the quotation with us now.
Hot Tags: clearcoat solutions, China, factory, manufacturers, quotation, low price, made in China
Related Products
Inquiry