High Efficiency Clearcoat RC-9000 Clearcoat has highest gloss, highest build, best exterior durability, highest end hardness and good adhesion results on metallic basecoats, good leveling. The application function is good and it is fast drying coat.
MULTI-PANEL CLEARCOAT RC-8000
A VOC compliant, two-component clearcoat designed for panel and multi-panel repairs in air dry and low bake applications. It delivers high gloss, fast cure, fast dust-free times and lower overspray.
ROCH® Colordefender™ Premium Appearance Clearcoat
RC-8000 2 Parts
Activator RC-G221/G222/G223 1 Part
Reducer RC-X110/X111/X112 0.2 Part
15-17 seconds in a Zahn #2 cup.
90 minutes at 70°F (21°F)
Accelerator/Fish Eye Eliminator/Flex Additive/Matting Agent
1K Basecoat RC-M series
For application over a properly prepared basecoat repair:
Mask the entire vehicle to protect from overspray.
Allow basecoat to dry 15-30 minutes prior to clearcoat application.
Extend basecoat flash to 30 minutes when applying several base color coats, tri-coat colors, or in cooler shop conditions.
Compliant 1.3 mm-1.4 mm*
HVLP 1.3 mm-1.4 mm*
Siphon Feed 50-55 psi at the gun
Gravity Feed 45-55 psi at the gun
HVLP 9-10 psi at the gun cap
*Refer to the manufacturer's directions for gun specific recommendations.
Apply 2 medium-wet coats. Flash 12-15 minute between coats.
Tips for Success
Avoid using accelerator if you plan to bake. You may get solvent popping In the clearcoat if you use accelerator and bake the clear.
|Flash between Coats||12-15 minutes|
|Flash before force dry||None|
|Cycle Time||15 minutes at 70°C|
|Dust Free||At cool Down|
|Time to Polish||3 hours after cool down|
|Time to Handel||30 minutes after cool down|
|Flash between Coats||12-15 minutes|
|Dust Free||40 minutes|
|Time to Polish||8 hours|
|Time to Handel||8 hours|
Panel repair is the approved procedure for clearcoat warranty repairs. This allows the refinisher to attain the recommended film builds.
Clean spray equipment as soon as possible with Lacquer Thinner.
SANDING / COMPOUNDING / POLISHING SANDING
Use 1500 grit wet or finer or use a foam interface pad with P1500 DA or finer.
Apply a thin ribbon of rubbing compound to the area that was sanded or contains sand scratches.
Maintain air polisher or variable speed buffer at 1400-1800 rpm. Remove excess finishing compound with a clean soft cloth prior to applying finishing polish.
Use a wool pad and an effective rubbing compound.
Apply a ribbon of polishing material to the area to be polished.
Maintain a variable speed buffer or an orbital polisher at 1400-1800 rpm.
Use a foam pad and an effective polishing compound. Keep the polisher/buffer moving at all times. Overlap each pass approximately 50%. As finishing polish begins to dry, stop polishing.
Wipe off excess finishing polish with a clean soft cloth.
Hand buff with a clean soft cloth as a finishing touch.
Tips for Success
Always use clean water to wet sand and add a few drops of soap to help clear the paper.
Always use a foam interface pad when DA sanding.
Use clean cloths and pads to insure that the clear does not get scratched with dirt.
All Values Ready To Spray
Standard Reduction Mix Ratio 2：1：0.2-0.5
|Theroetical Coverage:||700 sq. ft. per RTS gallon at 1 mil|
|Recommended Dry Film Thickness:||2.0 – 2.4 mils in 2 coats.|
|Packaging||5L x 4 tins/ctn, 1L x 12 tins/ctn|
|Shelf Life||5 years|
VOC REGULATED AREAS
These directions refer to the use of products which may be restricted or require special mixing instructions in VOC regulated areas. Follow mixing usage and recommendations in the VOC Compliant Products Chart for your area.
SAFETY AND HANDLING
For industrial use only by professional, trained painters. Not for sale to or use by the general public. Before using, read and follow all label and MSDS/SDS precautions. If mixed with other components, mixture will have hazards of all components.
Ready to use paint materials containing isocyanates can cause irritation of the respiratory organs and hypersensitive reactions. Asthma sufferers, those with allergies and anyone with a history of respiratory complaints must not be asked to work with products containing isocyanates.
Do not sand, flame cut, braze or weld dry coating without a NIOSH approved air purifying
respirator with particulate filters or appropriate ventilation, and gloves.
Keep it for 15 to 20 minutes after spray, and then bake it.
1.Keep the baking room dry when baking, otherwise the gloss will disappear.
2.Add 15‰ quick dry liquid for fast solidity.
3.Choose the right hardener according to the tempreture.
It is suitable to spray the whole car body.
2017 Automechanika Dubai
PACKING & DELIVERY
BENEFITS WE OFFER
Help customers achieve their goals while driving productivity from the front of the body shop to the back. For coatings systems engineered for easy, quick and accurate application. For localized business and marketing support solutions. And for pragmatic innovations that simplify and expedite the refinish process.
With our products and support, we help body shops focus on driving their businesses forward.
1. Do you charge for the samples?
(A) According to our company policy, the samples are free, we only charge the freight. And we will return the freight if you set the order .
2. Can you produce the product according to customer's requirement?
(A) Sure, we are professional manufacturer, OEM is welcome.
3. What about the quality?
(A) We can provide you samples for quality inspection. If you order to us ,we must promise the quality , if some quality problem happened, we can have a negotiation of the compensation and sign agreements ,and our after-sales department will perform the duties as the agreements.
If you want the High Build Car Paint for body shop, welcome to buy the quality products made in China with our factory. As one of the professional manufacturers in China, we will offer you quality products with low price. Consult the quotation with us now.
If you want the auto clearcoat, welcome to buy the quality products made in China with our factory. As one of the professional manufacturers in China, we will offer you quality products with low price. Consult the quotation with us now.